Blade BLH8000 Instruction Manual download pdf (Page 5)

The Battery Charging Process

1. Connect the AC power supply to the charger.

2. Connect the AC power supply to an AC power source.

The green LED blinks.

3. Connect the battery to the charger. The red LED

blinks, indicating charging. When the battery nears

full charge, the red and green LEDs blink, indicating

cell balancing.

4. Disconnect the battery when the green LED glows

solid.

Charging the Flight Battery

Charger Speciﬁ cations

• Input Voltage: 10.5–15V DC

• Charge Current: 3.5A

LED Indications

Green Blinking: Ready to Charge

Red Blinking: Charging

Red & Green Blinking: Cell Balancing

Green Solid: Charging Complete

Red Solid: Error

CAUTION: Overcharging a battery can cause

a ﬁ re.

NOTICE: If using a battery other than the included

Li-Po battery, refer to your battery manufacturer’s

instructions for charging.

1a 1b

* Old versions of the DX4e and DX5e (with 2-position channel 5 switches) are not recommended for the 350 QX2. Only Smart Mode and Stability Mode will be available with GPS On.

Transmitter Setup

CAUTION: When using a Futaba transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to your Spektrum module manual for binding

and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.

Transmitter Model

Type

Reverse

Setup

Throttle Cut

Setup

Mode Setup Switch Positions Throttle Cut Return Home

DX4e (New)*

w/3-position

switch

N/A N/A N/A N/A

Position 0 = SMART Mode

Lower throttle trim

until motors stop

turning

Press and Hold TRAINER/

BIND Release to EXIT

Position 1 = AP Mode

Position 2 = Stability Mode

DX5e (New)*

w/3-position

switch

N/A N/A N/A N/A

Position 0 = SMART Mode

Lower throttle trim

until motors stop

turning

Press and Hold TRAINER/

BIND Release to EXIT

Position 1 = AP Mode

Position 2 = Stability Mode

DX6i Acro

THRO-N

ELEV-N

GEAR-R

AILE-N

RUDD-N

FLAP-N

ACT

Travel Adj: GEAR POS (0) GEAR: ↑100%;

GEAR/F MODE POS (1) GEAR: ↓40%

FLAPS: Norm ←↑100; LAND ↓100

MIX 1: ACT; GEAR → GEAR ACT

RATE D 0%; U + 100%

SW MIX TRIM INH

SUB TRIM THRO ↑ 15-20%

GEAR 0; Mix 0 = SMART Mode

Press throttle cut

FLAP Position 0 = OFF

FLAP Position 2 = Return

Home

GEAR 1; Mix 0 = AP Mode

GEAR 1; Mix 1 = Stability Mode

DX7/7SE Acro

FLAP-R (6)

Others-N

N/A

Travel Adj: GEAR (0)↑100%;

GEAR (1) ↓40%

MIX 1: FLAP → Gear OFF/ON

RATE → -50%

SW: MIX OFFSET: 0

GEAR (0); Mix (0) = SMART Mode

Lower throttle trim

until motors stop

turning

FLAP Pos 0

= OFF

FLAP Pos 1

= Return Home

GEAR (1); Mix (0) = AP Mode

GEAR (1); Mix (1) = Stability Mode

DX7S Acro

AUX1-R

Others-N

Set To:

Trainer

Switch Select:

Move Gear to F MODE (F MODE:GEAR)

Leave FLAPS as AUX1

Set All Others to INH

MIX 1: GER > GER

RATE: 0%

-100%

OFFSET: 0%; TRIM: INH; SW: Mix0

F MODE (0) = SMART Mode

Press

Trainer

FLAP Pos 0 = OFF

FLAP Pos 2 = Return

Home

F MODE (1) = AP Mode

F MODE (1); HOLD (1) = Stability Mode

DX8 Acro

AUX1-R

Others-N

Set To:

Trainer

Switch Select: F-Mode to Gear;

Flap to Aux 1

All Others to INH

F MODE (0) = SMART Mode

Press Trainer/Bind

FLAP Pos 0

= OFF

FLAP Pos 2

= Return Home

F MODE (1) = AP Mode

F MODE (2) = Stability Mode

DX6/DX9/DX18 Acro

AUX1-R

Others-N

Set To:

I (BIND)

Channel Assign: NEXT

1-4: N/A 5 Gear: B

6 AUX1: H 7-10: INH

B (0) = SMART Mode

Press I (BIND)

D (FLAP) Pos 0 = OFF

D (FLAP) Pos 2 = Return

Home

B (1) = AP Mode

B (2) = Stability Mode

1 2 3 4 5 6 7 8 9 10 ... 17 18

Comments to this Manuals

No comments

Blade BLH8000 Instruction Manual Page 5

Comments to this Manuals

Related products and manuals for Remote controlled toys Blade BLH8000