Blade mQX Instruction Manual download pdf (Page 5)

Battery Charging

Celectra™ 1-Cell 3.7V Variable Rate DC Li-Po

Charger

1S 3.7V 500mAh 12C Li-Po Battery Pack (E-ﬂite

EFLB5001S)

TheBlademQX1SLi-PobatteryfeaturesaJSTconnec-

torthatallowsyoutosafelychargeyourbatterypack

whenusedwiththeincludedLi-Pochargerandcharge

adapter.Theincludedightbatteryissafetochargeup

to2C(1.0Amp).

UseonlyHorizonHobbyapprovedbatterypacksand

chargerscompatiblewiththisproduct.

1.Connectthepowersupplytoanappropriatepower

source.

2.InserttheoutputplugfromthepowersupplyintothepowerinputslotoftheVariableRateCharger.

3.Selecttheappropriatechargecurrentforyour

batterybypushingthe+or-,whicharethesmallerbuttonstotherightandleftofthemiddlebutton.(When

chargingyour500mAhbattery,setthechargerto0.7amps.)

4.ConnectthechargeadaptertotheChargerlead.Matchthereddotsonboththechargeadapterandthe

Chargerlead.

5.ProperlyconnectthebatterytotheChargerlead.Matchthereddotsonboththebatteryandcharger

connectors.

6.Pressandreleasethestartbuttononthevariableratecharger(thelargestbuttoninthemiddle).

Afullychargedightbatterycanyieldighttimesofuptotenminutes.

AC Power Supply Cautions and Guidelines

NEVERattempttopowerthechargerfromanACoutletwithouttheuseofaproperACtoDCadapter/power

supply.

DONOTconnectchargedordischargedLi-Pobatteriesifthepowersupplyisconnectedtothechargerwhilethe

powersupplyisnotconnectedtoapowersource.Doingsowilldischargeandpossiblydamagethebatteries.

ForACoperation,onlyuseanE-ite®6Vpowersupplywiththischarger.DONOTusea12Vpowersupplyor

propertydamageandinjurycouldoccur.

1.Lowerthethrottleandthrottletrimtothelowestsettings.

2.Poweronthetransmitter.

3.FliptheQuad-Copterupside-downandinstallthebatterybyslidingitintothebatterymountingslotbelowthe

PCBoard.Slidethebatteryintotheslotswiththelabelfacingupwardsothatthebatterykey,moldedintothe

batteryend-cap,comesincontactwiththekeyonthebatteryslot.(ThiskeyindicatestheFRONToftheQuad-

Copterin“+”ightmode).

4.Connectthebatterycabletothe4-in-1controlunit.

NOTICE:DonotallowtheQuad-CoptertomoveuntiltheLEDonthe4-in-1controlunitissolidblue(notblinking).

CAUTION: AlwaysdisconnecttheLi-Pobatteryfromtheaircraftwhennotyingtoavoidover-

dischargingthebattery.Batteriesdischargedtoavoltagelowerthanthelowestapprovedvoltagemay

becomedamaged,resultinginlossofperformanceandpotentialrewhenbatteriesarecharged.

Installing the Flight Battery

1 2 3 4 5 6 7 8 9 10 ... 67 68

No comments

Blade mQX Instruction Manual Page 5